-
Globs on Top of Wooden Floor Tile
I’m new to 3D printing Filament, only every done resin before. I’m using the anycubic k…
Started by: Holly Tyminski
in: Resolving 3D Printing Problems
- 2
- 4
-
3 years, 4 months ago
Nicholas Jebson
-
Rampage Castle as a basis for building modules for Bolt Action
I would like to use the already printed parts of Rampage Castle as a basis for building modules for…
Started by: Amahu
in: Getting Started
- 4
- 6
-
3 years, 5 months ago
Anonymous
-
Is there a comprehensive dungeon package?
I am a at a bit of a loss as to what sets I would need to do an expandable dungeon. What should I …
Started by: dweitz27
in: Getting Started
- 3
- 3
-
3 years, 7 months ago
SC
-
Tudor wall with chimney
Is there a Tudor wall with chimney to continue a wall above the Tudor fireplace file? And is there …
Started by: h.peless
in: 3D Printed Terrain for Tabletop Wargames
- 4
- 6
-
3 years, 8 months ago
Anonymous
-
Clorehaven Ruins now available on Terrain Tinker
With the Ruins now ready to go on Terrain Tinker, it’s really easy to plan out OpenLOCK build…
Started by: Nicholas Jebson
in: Clorehaven and the Goblin Grotto Kickstarter
- 1
- 1
-
3 years, 9 months ago
Nicholas Jebson
-
More Bundles Please
I know you usually do bundles for Kickstarter, but more bundle specials would be awesome. I’d…
Started by: Donald Judd
in: Model ideas and update suggestions
- 5
- 5
-
4 years ago
aegis_vdk
-
Tudor walls infill
Question. Why do the models for clorhaven and winterdale show brick underneath the Tudor daub as op…
Started by: drphilipcohen
in: Clorehaven and the Goblin Grotto Kickstarter
- 3
- 4
-
4 years, 1 month ago
Nicholas Jebson
-
Inn of the Welcome Wench
So I am wrapping up the Inn of the Welcome Wench on the Roof printing now and I am about a third th…
Started by: Brian Etty
in: Clorehaven and the Goblin Grotto Kickstarter
- 2
- 3
-
4 years, 1 month ago
Brian Etty
-
Schist walls D section
Hi chaps
Friendly poke that the bottom of the D section of the generic schist wall needs some patch…
Started by: James Jones
in: Clorehaven and the Goblin Grotto Kickstarter
- 3
- 5
-
4 years, 2 months ago
James Jones
-
What should it look like?
I matched my settings to the recommended settings I found on this website. Heat, brim. .2mm layer …
Started by: Scott Andreu
in: Resolving 3D Printing Problems
- 3
- 5
-
4 years, 4 months ago
Stephaned38
-
Problems with IA Schist Wall (Both with and without Top Locking)
I have a problem printing the IA schist wall, both with and without top locking. The bottom of the…
Started by: Ronald Rickard
in: Resolving 3D Printing Problems
- 2
- 8
-
4 years, 5 months ago
Nicholas Jebson
-
BA-AS-Wall for other sets
All in the title. Is there any prospects on the horizon of a BA-AS-Wall for other sets? To attach w…
Started by: seanwmcinnes
in: 3D printed terrain for Dungeon Masters
- 4
- 4
-
4 years, 5 months ago
Nicholas Jebson
-
Springy Clip Caps
I’ve been using the springy OpenLOCK clips found on Thingiverse with great success – ht…
Started by: Ronald Rickard
in: Model ideas and update suggestions
- 2
- 2
-
4 years, 5 months ago
Nicholas Jebson
-
The Evil Under Clorehaven advice
Has anyone here run the Evil Under Clorehaven Scenario that was released during the kickstarter? I&…
Started by: martinichamber
in: Clorehaven and the Goblin Grotto Kickstarter
- 2
- 2
-
4 years, 5 months ago
Nicholas Jebson
-
More Roof Options
More single story roof options would be nice. A wooden shake (similar to stone barn) style made fo…
Started by: rob61374
in: Model ideas and update suggestions
- 4
- 8
-
4 years, 6 months ago
Nicholas Jebson
-
Schist Low Walls – No L 90 degree column
Hi,
I’m looking to use the low walls to create a 3D Altar Quest board. However I can’t …
Started by: dreadknot69
in: Clorehaven and the Goblin Grotto Kickstarter
- 2
- 2
-
4 years, 8 months ago
Nicholas Jebson
-
Inn of the Welcome Wench
I am finishing up the Inn of the Welcome Wench and I am a bit concerned with the roof. I have the l…
Started by: Brian Etty
in: Clorehaven and the Goblin Grotto Kickstarter
- 3
- 8
-
4 years, 8 months ago
Nicholas Jebson
-
Clorehaven and Rampage Castle
I wanted to ask if the Clorehaven parts would work with the Rampage Castle packs, I wanted to use t…
Started by: insanejigsaw
in: Clorehaven and the Goblin Grotto Kickstarter
- 3
- 4
-
4 years, 11 months ago
Nicholas Jebson
-
Cloverhaven cottage
I printed the small roof for the cottage and it didn’t fit properly. It fit perfectly over th…
Started by: richard Sotomayor
in: Clorehaven and the Goblin Grotto Kickstarter
- 2
- 4
-
5 years ago
Nicholas Jebson
-
Overhangs causing fails on A-TudorFirePlace-v1.1
Hello,
There are some overhangs in the piece “A-TudorFirePlace-v1.1” that are causing p…
Started by: feday
in: Model ideas and update suggestions
- 2
- 3
-
5 years, 5 months ago
Nicholas Jebson
