Description
A place of worship for paladins and clerics to the chosen god of their pantheon. Also good in a pinch when you need sanctuary against an evil demonic horde.
To build the Chapel as pictured, you will require pieces from other sets, including Rustic Stone Floors, Rustic Stone and Wood Stairs, Schist Walls , and Clip Cap sets. To assemble the Chapel and other buildings of Clorehaven you can download the Assembly Guides.
Link to Door Assembly Guide.
Updates:
- 26 February 2020 (version 1.1) Locking pins adjusted on Q-Entrance and Q-Window.
Notes for Clorehaven Chapel Expansion:
- Right-click on the image below and “Save As” to download the reference sheet for this pack.
- Product measurements can be found in the image gallery.
Chapel Top Locking Variations Reference Sheet
Shaun Kantor (verified owner) –
I am struggling to print the Q Window Schist with Corbels. The center section of the window is breaking or leaning over in every print. Is there a specific setting I need to get this to print stable?
Nicholas Jebson –
Hey Shaun
We are going to have a look at it and see if it needs updating.
Cheers
Nick
ragnarok66 (verified owner) –
Hi !
I want to print the version with locking system. But the Q-Entrance-Schist-Chapel-w-locking-pins-v1.0 pins should be move (or duplicate) because they are overlapping with the two A-Window-Schist-Chapel-v1.0 on the top. The pins does not fit in the opening under the windows section. It is not absolutly necessary, but it could be a good modification.
thx !
Stephane
Nicholas Jebson (verified owner) –
Hey Ragnarok, I can see what you mean, we will update this soon with the pins slightly wider so that the A walls can fit comfortably.
jaap (verified owner) –
Any chance that we can get the roof pieces of the chapel broken up in smaller parts? My printer struggles with large prints like these…
Sam Campbell (verified owner) –
The Modular Shingle Roofs are available here for smaller modular roof pieces. https://www.printablescenery.com/product/modular-shingle-roof/ otherwise you can use this helpful guide to cut the roof pieces, but you will need to print with supports if you do this: https://blog.prusaprinters.org/cut-stl-models-3d-printing-meshmixer/
jpintos (verified owner) –
In the assembly guide Item # 11 for Level 1 is L-Column-Schlist-v1.0 , but it only connects to a single wall. I think O-Column-Schlist-v1.0 or I-Column-Schlist-v1.0 would be better. Or are the inside-looking clip slots intended for some decoration?
Sam Campbell (verified owner) –
You are correct, O-Column would be better here. I think I switched it out when removed the doorway and in its stead put the AS floor tile.
David Aleshire (verified owner) –
What stairs were used in the bell tower?
David Aleshire (verified owner) –
ignore my previous question, im dumb and didnt read instructions
Mike –
Don’t worry about it, we’ve all been there! 🙂
mrebivens (verified owner) –
Any possibility of adding a G-Window-Schist Chapel?
Mike –
Hi Mrebivens,
I’ll add your suggestion to our list of possible model updates when we next look at the chapel expansion. That sounds like a good idea!
Michael Riecken (verified owner) –
Beautiful work.
The instructions are a little out of date, but it wasn’t an impediment. I didn’t find them until I was done anyway.
Instructions: https://www.printablescenery.com/wp-content/uploads/2024/12/Chapel.pdf
One thing is that I would have liked the bells to be elevated above the wall in the belfry. Even if by just 5mm.
We’ll be using this in a battle map for S01E05(?) of NatOneClub: Misfits or Heroes
I don’t think our paint job will be nearly as good as yours though. Always amazing work. We’re all huge fans.
Joanne Boorer (verified owner) –
Hi Michael, thanks for your feedback. I will pass your suggestions on to the team.