My Account 
Description
The parapets and curtain walls of the Normans provided safety for their troops. Be it from their Saxon rivals or the weather, they provided shelter from rain and arrows. Non-structural, they were often hastily built on strategic sites before more permanent buildings like the keep were constructed.
Updates:
- 19 December 2022 (version 1.4) Norman-Fort-Walls-Wall-Shortest has been added.
- 17 March 2023 (version 1.5) Wall extensions added.
- 30 March 2023 (version 1.6) Extensions added for the Gate.
- 15 August 2023 (version 1.7) A Hexagon wall option was added and Transition steps for the extensions.
- 18 October 2023 (version 1.8) Hexagon wall extension added.
Notes for the Norman Fort Walls:
- Right-click on the image below and “Save As” to download the reference sheet for this pack.
- Small printer reference included in the zip file.
- Product measurements can be found in the image gallery.
- First Published version 1.3
ryleylink5c293fc3ad4c7 (verified owner) –
Would it be possible to have an inside corner piece in a future update? I would love to be able to make a but more intricate wall designs. Thanks!
Jo Boorer (verified owner) –
Yes, this will be included in our upcoming wall extensions and corner towers update.
ragnarok66 (verified owner) –
Do you think it would be possible to include small holes to place magnets in so that the walls can hold together more easily?
Thanks by the way, great job once again!
Jo Boorer (verified owner) –
Good idea.
We will add this to the model updates list.
Jay Killeen (verified owner) –
I was a bit disappointed that the size of the pieces are not to some kind of inch scale. It is making it difficult to make a connected shape (ie square) once you had feature peices like the gate and towers.
Adam Usher (verified owner) –
I noticed the off size as well. I just printed an even number of towers, 4 in my case and then as long as you have them on opposite sides of each other then the size is fine.
justin.littlehammer (verified owner) –
Are you planning to make a set of inner walls? Basically taller walls that would make up an interior area that is protected that if the outer walls were taken by the enemy the defenders can still shot down on them? Likely where the keep and kings quarters would be located. Not sure if the kings gate would still work, or need to be scaled as well.
Or do you have a recommended scale to print up to for the inner walls?
Jo Boorer (verified owner) –
We have wall extensions in the pipeline to make the walls higher.
louanders (verified owner) –
I love all these pieces but I was also bothered they weren’t of a scale that is compatible with my other terrain.
Also, the largest stretch of wall is too big for the Ender 3. We have short, shortest, and long. Any chance of a medium?
Jo Boorer (verified owner) –
I will add your suggestion for the Medium wall to our list of possible updates.
If you put the largest wall diagonally on the build plate it will fit.
I have included below a link to help with scaling your models to your preferred size.
https://www.printablescenery.com/2016/11/13/scaling-printable-scenery-models/
louanders (verified owner) –
Thank you. I rotated it. My question wasn’t so much about scaling the model for 32mm, 28mm etc… (know how to do that)as Jay’s comment above – the fact that they aren’t on an inch scale means they won’t fit alongside terrain using a one-inch grid. They could sit above it, of course, but you couldn’t say, put a 4inch x 4inch ground tile in the corner and have it line up.
Roem (verified owner) –
Would it be possible to have an angle wall that would allow us to do hexagon or similar shapes with the walls?
Jo Boorer (verified owner) –
That is a good suggestion I will add this to the update suggestion list.
Roem (verified owner) –
Will the gate be getting an updated model for use with the wall extensions?
Jo Boorer (verified owner) –
Yes we can do that.
justin.littlehammer (verified owner) –
Is it possible to get a transition piece for the wall extensions and the original? I was thinking maybe two types. One is a transition that is mostly just a set of stairs. The other would be stairs that transition midway to a landing and then stairs to the next level.
Jo Boorer (verified owner) –
I will add this to the list of possible updates.
David Dickson (verified owner) –
Loving these walls! One question: I’m not sure what the negative spaces are for beneath each of the walls/towers. Are these intended to stack on top of other walls/structures somehow?
Jo Boorer (verified owner) –
Yes, these are for those who wish to have higher walls by using the extensions included in this zip file.
aaron currence –
Any possibility to get a version of the towers in this set with crenellations instead of the roof?
Jo Boorer (verified owner) –
Thanks for your suggestion will put this on our model update list.
Kerry Thomas (verified owner) –
Please excuse what may be a stupid question, I’m new to this and started printing on the weekend. I’m using a Neptune Elegoo 3 Pro and have printed great walls. I cannot seem to slice some files though – notably the tower from this set. I’m using Cura 5.5. Any advice please
Jo Boorer (verified owner) –
Try turning on the build plate.
AlexOzerov (verified owner) –
Hello! Please consider adding a Hexagon Fort Wall option with a cut on one side only (for connecting at right angles to buildings) and perhaps another option with cuts turned in the other direction (for a larger number of possible combinations) Thank you for your work! You are best!
Jo Boorer (verified owner) –
Hi Alex.
Thanks for your suggestion I will add it to the models update list.