Description

For as long as she could remember, the door to the cellars had always been locked. Yet here it was, sitting wide open, the smell of damp earth and long rotted vegetation emanating from within. She placed her hand on the ancient oak door and wondered who had found the key. From within the cellar, she heard a rustling.

Updates:

(version 1.1) Have replaced the Z-RPG-CastleDoor-v1.1 after a small mesh repair.
12 June 2017 (version 1.2) Small mesh repairs made to A-RPG-CastleDoor-v1.0, G-RPG-CastleDoor-v1.0, G-Step-RPG-CastleDoor-v1.0, P-RPG-CastleDoor-v1.1, X-RPG-CastleDoor-v1.1.
14 July 2017 (version 2.2) The Castle Door supports have been redesigned to facilitate easy removal.
17 July 2017 (version 2.3) Contains a step option for all Castle Doors.
13 March 2018 (version 2.4) Updated to Triplex.
22 May 2018 (version 4.0) Correction made to Q Tile pins. Latest version of Triplex.
1st February 2019 (version 4.1) Filament door connection.
20 February 2023 (version 4.2) AS-Door without step added.

Notes for Castle Doors:

Right-click on the image below and “Save As” to download the reference sheet for this pack.
Product measurements can be found in the image gallery.

Castle Doors (with steps) Reference

Castle Door OpenLOCK STL

Castle Doors (without steps) Reference

Castle Door OpenLOCK STL

Additional information

Recommended Printer	FDM or resin printer
Terrain Tinker	Available
Infill	100% for resin printing, 10% to 15% for most parts but increase to 20% for thin upright parts such as door frames for added strength
Layer Height	0.05 high quality on resin printers, .2 for Normal Quality .1 for High Quality (.2 Layer height is recommended)
Supports	requires supports for resin printing, Prints without Supports
Scale	32mm Heroic & OpenLOCK

Use this tool to find the percentage needed to scale your model up or down when printing.
The highlighted row shows the model's current scale and other rows show what percentage to print at to reach that scale.
To set a custom scale, use the calculator in the bottom row.

Name	Millimeters mm	Ratio	Scale %
10mm Wargames & N Scale	10	1:159	31.3%
15mm Wargames	15	1:116	46.9%
HO Scale	20	1:87	62.5%
OO Scale	22	1:76	68.8%
28mm Wargames	28	1:62	87.5%
32mm Heroic & OpenLOCK	32	1:54	100.0%
			-

mm is the height based on the measurement from the bottom of the feet to the eye height of the average human
Height is not the same as Base Size (A 28mm miniature will often have a 25mm round base)

Creating Magnetic Dungeon Tiles with OpenLOCK

Posted on July 21, 2025July 22, 2025 by Sloane Dougherty

This article will show you how to use the OpenLOCK Magnetic Clip to build fully interchangeable dungeons with magnets. Once you’ve built a collection of these magnetic clips, you can swap and change dungeon layouts in no time. The Magnetic Clip is an OpenLOCK adapter option. It is interchangeable with other OpenLOCK clips but is… Read more

Removing supports from the OpenLOCK ports

Posted on August 24, 2017July 22, 2025 by Dee Barker

Horizontal OpenLOCK ports print with small supports to support the overhangs in the port mouth. You need to remove these supports post-printing before you can insert the OpenLOCK clips. We recommend using some needle-nosed pliers for this task. You can use the pliers to grip and twist the two supports in each port, breaking them… Read more

6 Comments

Comments

Ian Bowley (verified owner) – May 16, 2017

Any tips to get the door to work? I have printed a few A panels out, and the door pins sheared each time. Looks like it may just be easier to put a paperclip wire through it.
- Ryan – May 17, 2017
  
  I have made a video on the Rampage Dungeon Door here. https://www.youtube.com/watch?v=ys9r073r4do
  
  The main thing is to cut all the supports away before you try to operate the hinge. Top and Bottom
gordie_v (verified owner) – January 31, 2018

Is it possible to add D-wall option with a door?
- Rex Foot – January 31, 2018
  
  We certainly could, i will add it to the To Do List.
  
  Looking at the “D is for Darkness” pack, there is a tile with door already, but we can get one done with this style of door if you wish.
Matthew Warren (verified owner) – September 29, 2018

I would like to maybe see a Q-RPG-CastleDoor-v2.2 as a double door or have a double door option
- Sam Campbell – October 1, 2018
  
  A double door is in the works but will not be part of this product as it is a completely new sculpt.
Jeff Tremblay – February 17, 2019

Best I can tell, there are no floors available which can be set on the outside of the X wall, correct? It’s not possible to link a square building to a large tower through that door. It would be incredibly useful for Lost Mines of Phandelver in the city of Thundertree. There’s a small cottage attached to a large tower and the only way in that tower is through the cottage.
- Sam Campbell – February 18, 2019
  
  We can have a look at developing a piece to fit.
- Jo Boorer – June 29, 2020
  
  Castle Floors has just been updated with a floor tile that goes around the X Wall called 5×5-X-TRP-Castle-Floor.
t.andersson (verified owner) – June 20, 2020

How to print the doors? As the file is oriented with a brim?
How do they connect to the arches, just snap fit or is the hole through the door supposed to be used somehow?
- Sam Campbell (verified owner) – June 22, 2020
  
  You can use a piece of filament to hinge the door in place.
t.andersson (verified owner) – June 22, 2020

Is it just me or does these doors feel backwards? (the hinge bing on the wrong side). Would simply mirroring the stl work?
- Sam Campbell – June 22, 2020
  
  Mirroring the STL would work.
davedamon (verified owner) – November 20, 2022

Are there any plans to add versions of the no-step doors with connectors on both sides?
- Jo Boorer – November 21, 2022
  
  Are you referring to the filament door connection so that it open in either direction?
davedamon (verified owner) – December 1, 2022

Sorry, I phrase my question poorly (and can’t seem to see a way to reply). I meant AS style door pieces so you can connect floor tiles on both sides of the door?
- Jo Boorer – December 2, 2022
  
  That makes more sense. I will add this to our model update list.
  In the meantime, it is possible in Terrain Tinker to print out a door with a floor on either side.
  https://www.terraintinker.com/
davedamon (verified owner) – February 19, 2023

Any update on AS style doors (with openlock connector spaces on both sides)
- Jo Boorer (verified owner) – February 20, 2023
  
  The AS Castle door has just been added to this product.
ciprian mitu – October 5, 2024

Does it work with resin printers?
- Joanne Boorer (verified owner) – October 7, 2024
  
  Our OpenLOCK range can be printed in resin.
  However, the OpenLOCK clips are designed to be printed in PLA.
  Customers using resin either glue these together or use Terrain Tinker to build their model before printing.
  https://www.terraintinker.com/