The Undead Sloop

$14.95

Any sales taxes will be calculated in the checkout.

The Undead Sloop comes in two versions: ballista and cannon. Included in the .ZIP file are: separate deck layouts, interior fittings such as barrels and boxes, a removable ‘wake’ that simulates ship movement, cannons, ballista, and rigging clips (original or undead).

The undead sloop prints in multiple parts. There is an optional set of ‘bone rigging’ that can be used to rig the ship.

To rig this model, check out the general Rigging Guide.

This product is part of the The Lost Ships

This product is delivered as a .ZIP file pack containing 3d printer files (STL files) for use on a home 3D Printer.

Description

The dreaded bone fleet ships leave many a sailor adrift in a sea of nightmares.

Updates:

13 May 2021 (version 1.1) The two main rear skulls of part Undead-Sloop-C have been filled to allow for easier printing.

Notes for The Undead Sloop :

Right-click on the image below and “Save As” to download the reference sheet for this pack.
There are two rigging options: undead or original.
Refer to pic in Gallery for ballista mounting instructions. This will need to be glued.
Mast measurements can be found in the gallery.
Product measurements can be found in the image gallery.

Undead Sloop Hull

Rigging

Each piece of rigging

You will need 6mm (1/4 inch) and 4mm (5/32 inch) dowel for the masts and black elastic string for the rope. You may need to sand the ends of the dowel to go into the mast holes easily.

Undead Sloop Interior

Undead Sloop Wake

Undead Sloop Fittings

Additional information

Recommended Printer	FDM or resin printer
Infill	100% for resin printing, 10% to 15% for most parts but increase to 20% for thin upright parts such as door frames for added strength
Supports	requires supports for resin printing, Prints without Supports
Layer Height	0.05 high quality on resin printers, .2 for Normal Quality .1 for High Quality (.2 Layer height is recommended)
Scale	28mm Wargames

Use this tool to find the percentage needed to scale your model up or down when printing.
The highlighted row shows the model's current scale and other rows show what percentage to print at to reach that scale.
To set a custom scale, use the calculator in the bottom row.

Name	Millimeters mm	Ratio	Scale %
10mm Wargames & N Scale	10	1:159	35.7%
15mm Wargames	15	1:116	53.6%
HO Scale	20	1:87	71.4%
OO Scale	22	1:76	78.6%
28mm Wargames	28	1:62	100.0%
32mm Heroic & OpenLOCK	32	1:54	114.3%
			-

mm is the height based on the measurement from the bottom of the feet to the eye height of the average human
Height is not the same as Base Size (A 28mm miniature will often have a 25mm round base)

Comments

iezcurra (verified owner) – June 22, 2018

Hello good afternoon.

Buy this model today and I do not understand what the pieces are for (Undead Sloop Interior and Undead Sloop Wake)

Sorry but it’s not very well explained,
But the design is spectacular

Thank you.
- Sam Campbell – June 25, 2018
  
  The Undead Sloop Wake is for placing the ship on to simulate the ship moving and the water lapping against the sides of the boat. The Undead Sloop Interior are separate interior floors for simulating role-play and combat inside the cabin and below decks. You do not need to print them to assemble the full model.
guthroth – January 13, 2019

Hi. What size is the download file please ? Thanks, Pete
- Jo Boorer – January 15, 2019
  
  The zip file for the Undead Sloop is 135MB.
seitoheiwa (verified owner) – March 8, 2020

Heyho,

a short question:

On part C of the hull in the back, with the two skulls – the teeth in the upper jaw seem impossible to print, and even on your pictures those are not there.
Will there be a redisgn where the teeth are for example connected?
- Nicholas Jebson – March 10, 2020
  
  Hey Seito
  We can add it to the list of updates, though its a difficult one as it still needs the gap to take the rigging lines.