Name: Sheriffs Office and Jail
Brand: Dungeons and Dragons
Availability: InStock

Sheriffs Office and Jail

$14.95

Any sales taxes will be calculated in the checkout.

The Sheriffs Office is a multi-part model. It contains a brick Jailhouse as a side building and has plenty of space for the placement of models throughout. The beams within the doorway are meant for printer support and can be removed to fit the door.

This product is part of the Time Warp Americas

Description

A Sheriffs Office must be well built, as it serves as both a headquarters for the sheriff and a jail for lawbreakers.

Updates:

10 July 2017 – 1.2 Contains the cut version of the Sheriff’s office for small printers.
4 April 2018 – 1.3 Adjustment was made to the scale of the Sheriff’s office for small printers.
8 August 2018 – 1.4 Jail without door added.
27 March 2019- 1.5 Locking pins and filament door connection have been added.

Notes for Sheriffs Office and Jail:

Right-click and “Save As” to download the below reference sheet.
A reference sheet for the small printer option is included in the zip file.

Additional information

Recommended Printer	FDM or resin printer
Infill	100% for resin printing, 10% to 15% for most parts but increase to 20% for thin upright parts such as door frames for added strength
Supports	requires supports for resin printing, Prints without Supports
Layer Height	0.05 high quality on resin printers, .2 for Normal Quality .1 for High Quality (.2 Layer height is recommended)
Scale	32mm Heroic & OpenLOCK

Use this tool to find the percentage needed to scale your model up or down when printing.
The highlighted row shows the model's current scale and other rows show what percentage to print at to reach that scale.
To set a custom scale, use the calculator in the bottom row.

Name	Millimeters mm	Ratio	Scale %
10mm Wargames & N Scale	10	1:159	31.3%
15mm Wargames	15	1:116	46.9%
HO Scale	20	1:87	62.5%
OO Scale	22	1:76	68.8%
28mm Wargames	28	1:62	87.5%
32mm Heroic & OpenLOCK	32	1:54	100.0%
			-

mm is the height based on the measurement from the bottom of the feet to the eye height of the average human
Height is not the same as Base Size (A 28mm miniature will often have a 25mm round base)

3 questions for Sheriffs Office and Jail

dale (verified owner) – January 5, 2019

What scale is this supposed to be. I just spent 24+ hours printing it, and it seems a bit to tall for standard 28mm western figures. I printed the Minners shack and it seemed like the proper scale so I did not double check on this before sending it to the printer. Great model otherwise.
- Matt Barker – January 5, 2019
  
  The Scale is 28mm, I have written a blog about scale here that may help https://www.printablescenery.com/2016/11/13/scaling-printable-scenery-models
blessedhorizonstudios (verified owner) – February 10, 2019

There are doors for this print but they don’t fit because the door jams have wooden angled pieces in them, thus stopping the doors from fitting in without cutting out that part of the model. Also the holes on this are great for 2.35mm(3/32″) tubing as pins but some of the others use the PLA 1.75 filament as a pin. I prefer the 2.35mm holes as I can use brass pins or Styrene tubing. Great print though!
- Sam Campbell – February 11, 2019
  
  These doors can be forced in with a bit of pressure.
Delaney Anderson (verified owner) – December 24, 2019

There is NO WAY, that door can be forced into that whole as said by the previous post. The door if you try to pit would be at an angle and looks bad. Those angled cross beams on the door do not allow the door to sit smooth and flush
- Sam Campbell – January 6, 2020
  
  The beams inside the doorway are removed to fit the door in. These are meant as printer supports for the top beam across the door way.