My Account 
Description
The clip clop of hooves on the cobblestones could be heard amongst the conversations along the busy streets of Clorehaven. Dust and grime settled in between the stones that had seen leather boots and carriage wheels smooth the surface over many years.
To build the streets and foundations as pictured you will require pieces from Schist Low Walls set.
Updates:
- 7 April 2020 (version 1.1) Grate for the street added.
Notes:
- Right-click on the image below and “Save As” to download the reference sheet for this pack.
- Product measurements can be found in the image gallery.
Low Walls Reference
Riser Reference
James Wykowski (verified owner) –
What paint scheme did you use for the street cobblestones? I assume you used your standard stone for the sidewalks.
Sam Campbell (verified owner) –
It was primed in black, The side walk stone was Dungeon Grey and Ash Grey, the street was Oak Brown, Leather Brown and Arid Earth.
Erik Corona (verified owner) –
I printed openlock clip from the free download package and it doesn’t seem to fit. I’m assuming we have to scale it down? If so, what percent?
Sam Campbell (verified owner) –
You will need to remove the printer supports from the outside edge.
Erik Corona (verified owner) –
Ah ha! Yes, removing the printer supports did the trick. Second question. There is space for 5 openlock clips. I can squeeze four but can’t get all 5 to squeeze in and lock. Am I just a weakling and should use more elbow grease or how many openlock clips should we be putting per side to connect the streets?
Sam Campbell (verified owner) –
Use 2 or 3, You do not need to use all the ports. The extra port options are mainly there if you want to attach smaller tiles of different configurations along the edge.
timmy.fagerlund (verified owner) –
Hello!
Is there some kind of end piece to cover the border with? Like a natural slope or something, so you can cover up the ugly holes on the sides of your street network as you plop it down on a mat or such?
Sam Campbell (verified owner) –
You can use https://www.printablescenery.com/product/clip-caps/ to cover ports if you need to.
ishnoe –
Does this set come with just the tops without the bases attached? I would like to attach them to a set of magnetic bases.
Sam Campbell (verified owner) –
The whole set is OpenLOCK pieces. You can cut them to fit to magnetic bases by sinking the model in the build-plate vertically or using this guide.
https://blog.prusaprinters.org/cut-stl-models-3d-printing-meshmixer/
pulluspuer (verified owner) –
Any plans to add curved tiles, such as V and F? Trying to build some “city hills” using rampage Castle walls as foundation, and want to top off with these streets. Would love to add some curves to my “hills” to mix it up a bit.
Sam Campbell (verified owner) –
It’s something we can have a look at in the future. There are a lot of pieces involved when curves and diagonals are added to the mix so it may end up being another product.
Shaun Kantor (verified owner) –
Any chance of a U tile with sewer grate in the center? I have printed mostly U street tiles and have not found a way to get the sizing and curbs to line up correctly to incorporate the E-sewer grate tile.
Nicholas Jebson –
sure, we can look into updating that.
Mark Stephenson –
What are the risers used for? is it to put steps to the side and the cobbles on top?
Nicholas Jebson –
You’ve got it in one mark. If you wanted the low steps to create a slightly raised section next to the road, the risers could sit next to it for the raised road section to go on top and line up with the steps.
robbcleaver (verified owner) –
Im also interested in a sewer for the U tiles. thanks
Mike –
Hi Robb,
Thanks for your input! I’ve added your suggestion to our list of model updates, so you should receive an email once it’s done!
Chris Emmett (verified owner) –
Any plans on doing smaller tiles for narrower side roads?
An E tile that had both road and footpaths on both sides would be amazing
Mike (Printable Scenery) –
Hi Chris,
Thats a good suggestion. Currently we don’t have any smaller but ill add it to our list of possible model updates for the future
John Fallara (verified owner) –
Would it be possible to get an AS piece of just the “curb” section? This would allow for “custom” streets to be in between using E and S tiles from other sets (and the added bonus of being able to put a sewer entrance “in the road” so to speak).
Mike (Printable Scenery) –
Hi John,
Clever thinking! Ill put it in our list of suggested model updates for when this one comes up for review in the future.
shedknight –
would this street and foundation work with the recently release king and county pledge that i backed for a tile set underneath? example like the Norman church or the Norman stone fort but if you can give me additional links or suggestions that you guys have for cool tile set for underneath like rivers ,dirt tiles or cart trails dig in the mud and etc. it be much appreciated for my next project board game table I’m going to make and PS love what you guys sincerely Adam the new guy.
Jo Boorer (verified owner) –
To go with the country and King range we would suggest roads from Shadowfey or Hagglethorn.
Check our blog on roads.
https://www.printablescenery.com/2022/09/12/3d-printable-roads-for-rpgs-dioramas-and-wargames/
Jay Killeen (verified owner) –
I love these tiles but really wishing there was a dead end tile so the street could finish.
Jo Boorer (verified owner) –
Thanks for your feedback.
I will add this to our model updates list.