Name: The Chapel
Brand: Age of Sigmar
Availability: InStock

Description

Though smaller than the splendid Gothic cathedrals, chapels still retain the distinctive style of Gothic architecture.

Updates:

19 June 2018 (version 5.7) Crosses can now be printed separately.
30 January 2019 (version 5.8) Locking pins have been added and filament door connection.

Notes:

Reference for the small printer included in the zip file.
Right-click on the image below and “Save As” to download the reference sheet for this pack.
Product measurements can be found in the image gallery.

Additional information

Recommended Printer	FDM or resin printer
Infill	10% to 15% for most parts but increase to 20% for thin upright parts such as door frames for added strength
Layer Height	0.05 high quality on resin printers, .2 for Normal Quality .1 for High Quality (.2 Layer height is recommended)
Supports	requires supports for resin printing, Prints without Supports
Scale	28mm Wargames

Use this tool to find the percentage needed to scale your model up or down when printing.
The highlighted row shows the model's current scale and other rows show what percentage to print at to reach that scale.
To set a custom scale, use the calculator in the bottom row.

Name	Millimeters mm	Ratio	Scale %
10mm Wargames & N Scale	10	1:159	35.7%
15mm Wargames	15	1:116	53.6%
HO Scale	20	1:87	71.4%
OO Scale	22	1:76	78.6%
28mm Wargames	28	1:62	100.0%
32mm Heroic & OpenLOCK	32	1:54	114.3%
			-

mm is the height based on the measurement from the bottom of the feet to the eye height of the average human
Height is not the same as Base Size (A 28mm miniature will often have a 25mm round base)

Comments

Nigel Guest (verified owner) – August 27, 2016

Matt tried emailing you! there does not appear to be any floor tiles when you download the chapel can you confirm and fix thanks Nige.
- Matthew Barker (verified owner) – August 29, 2016
  
  Hi, I have updated the file pack and now it contains the floor tiles
ahellyer – November 27, 2016

HI, how high is each section. I am about to get a printer with 10cm maximum print height. Thanks, Andrew
- Matthew Barker (verified owner) – November 28, 2016
  
  All the models have been cut to fit inside a 100 x 100 x 100 build volume. so you can print out the parts. If I was you I would get a bigger print bed like the Prusa i3 Mk2 then you can print out the models in 1 hit
thomas.heider (verified owner) – April 21, 2018

Hi! Is it possible the get the crosses extra in a file? I’ve printed this and some are came out really bad. But I can’t replace them.
- Matt Barker (verified owner) – May 1, 2018
  
  Hi, do you mean the crosses on the top of the chapel?
barry (verified owner) – June 14, 2018

I’m having the same issue as Thomas Heider.

It’s the small crosses on the sides that are problematic. I think there are two different sizes, the smaller ones are a bit lower and the higher crosses are slightly larger. I’ve printed this a few times now and these crosses just aren’t printing well. A few of the lower ones turned out okay but the higher ones are all messed up.

It’s mainly the circle around the cross that misprints; it’s just too thin and has too steep an angle so the next layer doesn’t stick and gets dragged about by the print head messing up whatever else prints next. There’s no good place to put a support since the topology below are pointed, toothy protrusions.

If you could make files of just these two sizes of crosses, perhaps a little beefier, maybe I could print some that would work to glue in the place of the ones that just don’t seem to want to print.
- Jo Boorer – June 19, 2018
  
  The Chapel has been updated to allow for the crosses to be printed separately.
miketheface (verified owner) – June 4, 2019

When printing the crosses separately, how many should be printed for each size?
- Sam Campbell – June 4, 2019
  
  1 large, 4 medium, and 18 Small crosses.