Gothic Spaceship Rooms

$13.95

Any sales taxes will be calculated in the checkout.

Rated 5.00 out of 5 based on 1 customer rating

(1 customer review)

The Gothic Spaceship Rooms set is perfect for futuristic science fiction board games, tabletop skirmish war games and role playing games. This set can be combined with the Gothic Spaceship Corridor and the Boarding Ship to create vast spaceship layouts.

Download the Rampage Base Pack for free to get the latest version of the OpenLOCK clip.

If you are a Kickstarter backer you must login to access your pledge

This product is delivered as a .ZIP file pack containing 3d printer files (STL files) for use on a home 3D Printer.

Description

The squad began unpacking rations. In the distance a clatter was heard, that echoed ominously though the vast ship, broken only by Sarge’s voice. “Break’s over maggots! Lock and load! We have incoming”.

This set contains for Gothic Spaceship Rooms:

5 room configurations
3 sliding doors -open, closed and damaged.

These tiles are based on a 30mm x 30mm square (each square is 30mm wide).

Notes for Gothic Spaceship Rooms:

Right-click on the image below and “Save As” to download the reference sheet for this pack.
Product measurements can be found in the image gallery.

Additional information

Recommended Printer	FDM or resin printer
Infill	100% for resin printing, 10% to 15% for most parts but increase to 20% for thin upright parts such as door frames for added strength
Layer Height	.2 for Normal Quality .1 for High Quality (.2 Layer height is recommended)
Supports	requires supports for resin printing, Prints without Supports
Scale	32mm Heroic & OpenLOCK

Use this tool to find the percentage needed to scale your model up or down when printing.
The highlighted row shows the model's current scale and other rows show what percentage to print at to reach that scale.
To set a custom scale, use the calculator in the bottom row.

Name	Millimeters mm	Ratio	Scale %
10mm Wargames & N Scale	10	1:159	31.3%
15mm Wargames	15	1:116	46.9%
HO Scale	20	1:87	62.5%
OO Scale	22	1:76	68.8%
28mm Wargames	28	1:62	87.5%
32mm Heroic & OpenLOCK	32	1:54	100.0%
			-

mm is the height based on the measurement from the bottom of the feet to the eye height of the average human
Height is not the same as Base Size (A 28mm miniature will often have a 25mm round base)

Creating Magnetic Dungeon Tiles with OpenLOCK

Posted on July 21, 2025July 22, 2025 by Sloane Dougherty

This article will show you how to use the OpenLOCK Magnetic Clip to build fully interchangeable dungeons with magnets. Once you’ve built a collection of these magnetic clips, you can swap and change dungeon layouts in no time. The Magnetic Clip is an OpenLOCK adapter option. It is interchangeable with other OpenLOCK clips but is… Read more

Removing supports from the OpenLOCK ports

Posted on August 24, 2017July 22, 2025 by Dee Barker

Horizontal OpenLOCK ports print with small supports to support the overhangs in the port mouth. You need to remove these supports post-printing before you can insert the OpenLOCK clips. We recommend using some needle-nosed pliers for this task. You can use the pliers to grip and twist the two supports in each port, breaking them… Read more

6 Comments

1 question for Gothic Spaceship Rooms

jonzucchi (verified owner) – September 6, 2019

I’m having trouble printing the room files. I have enlarged the files to be 28.6% bigger so they take up almost the full size of the bed. I’ve tried printing a few different room files after running them through Slicer. I get diagonal lines that cause a crash and occur outside of the design’s build path. I’m in the process of having a friend try and print so not completely confirmed yet. I was wondering if anyone else has had problems with any room files, such as the cross room.
- Sam Campbell – September 6, 2019
  
  Can you please send open a ticket with [email protected] and we can help troubleshoot any printing issues.
Thomas Garrison (verified owner) – February 2, 2021

Just downloaded the Gothic Spaceship bundle. I see the recommended infill is 20%. I can shave a few hours here and there going with 15% or even 10% usually on most 3D prints. I was wondering how “locked in” you are to recommending that 20%? Did you have bad results with lesser infills? Thanks in advance.

-Tom G
- Nicholas Jebson – February 2, 2021
  
  yeah 10% is fine and is what we generally now recommend. 20% was our old go-to when the printers were not as precise as they are now.
Rated 5 out of 5

dbroadway87 (verified owner) – April 6, 2022

anyone got a rough idea of how long each piece should take to print, its been a while since i used my printer and slicing with Cura on the room with 4 openings its suggesting 1 day and 4 hours. is that about right?
- Mike (Printable Scenery) – April 7, 2022
  
  Depending on your slicer settings that should be about right. I would put your infill at 10% and maybe up your printer head speed to quicken the print time